Gene Trask
Member
I just wanted to check to see if my Roxor should stay running if I disconnect the battery.
Alternator check
- Thread starter Gene Trask
- Start date
- Joined
- Apr 20, 2020
- Messages
- 831
- Points
- 63
- Location
- Palmer, AK, USA
- Roxor #
- 7262
- Roxor Ownership
- Roxor Owner
Why would you disconnect it with it running? It has an ECM, are you trying to kill it?
Buckpasser
Member
It won’t.
Gene Trask
Member
Ok thank you. I was trying to check the alternator to make sure it was charging.
It was not rasing the voltage on the battery when it was running. "I think" it was just the belt was loose, I am getting a consistent 14v now.
Thank you.
It was not rasing the voltage on the battery when it was running. "I think" it was just the belt was loose, I am getting a consistent 14v now.
Thank you.
- Joined
- Apr 20, 2020
- Messages
- 831
- Points
- 63
- Location
- Palmer, AK, USA
- Roxor #
- 7262
- Roxor Ownership
- Roxor Owner
Future reference. Disconnecting the battery while its running is not the right way to troubleshoot anything. If it were charging, seeing no reference voltage would cause the regulator to spike, sending full voltage out. That would likely smoke the ECM.
- Joined
- Mar 10, 2019
- Messages
- 2,316
- Points
- 113
- Location
- Hurricane, WV, USA
- Roxor #
- 2507
- Roxor Ownership
- Roxor Owner
You could also use a multi-meter
Campyman
Active member
X2. Use a volt meter. If it's over 14v when running your fine
Gene Trask
Member
In the end the battery is bad. With a new battery the Roxor cranks right up.
Now I have a different problem!
Even without the key, the instrument panel is going through its startup routine about every 5 seconds. It comes one all indicators are lit (except for the battery) the needle goes over and back, then it cuts off. 5 seconds later again.
When I turn the key on it goes normal.
I am unplugging the main power to preserve the battery.
I have un plugged the switch, then the ECM, one side at a time on the instrument cluster, and it still does it.
I am going to try today cleaning fuses and relays.
Any suggestions would be great.
I am in mud and sand with salt water and brackish water, every day.m
Now I have a different problem!
Even without the key, the instrument panel is going through its startup routine about every 5 seconds. It comes one all indicators are lit (except for the battery) the needle goes over and back, then it cuts off. 5 seconds later again.
When I turn the key on it goes normal.
I am unplugging the main power to preserve the battery.
I have un plugged the switch, then the ECM, one side at a time on the instrument cluster, and it still does it.
I am going to try today cleaning fuses and relays.
Any suggestions would be great.
I am in mud and sand with salt water and brackish water, every day.m
1BB
Member
- Joined
- Nov 9, 2019
- Messages
- 60
- Points
- 18
- Location
- Church Point, LA, USA
- Roxor Ownership
- Looking to buy
It sounds like you may have a ground problem due to the salt water corroding a connection some where, and it's feeding back through the dash causing it to go crazy. I've seen this happen countless times on older vehicles where the roads are salted in the winter. Try removing the key so everything should be off, but the dash is going crazy, and then pull out one fuse at a time to see if you can make it stop. If it is still going crazy, put the fuse back in and go to the next one. If it stops, you have narrowed down which circuit to search for the problem.
Gene Trask
Member
Thank you I will give that a try to see how it goes.
please help where is the voltage regulator
- Joined
- Apr 20, 2020
- Messages
- 831
- Points
- 63
- Location
- Palmer, AK, USA
- Roxor #
- 7262
- Roxor Ownership
- Roxor Owner
many Thanks can it be replaced or maybe checked...changed out old alternator with new 90 amp all checked out after three days would not crank checked battery fluid was low added water will not hold up checked the flow to battery from alternator 11-10-6 - 7 amps battery runs down ? any thoughts on what's going on
